AVIRON COLD ROAD EMULSION

General information                Cold road emulsion was specially developed to perform and apply surfaces repair layers where spray trucks where difficultly applicable. Due to its low viscosity this emulsion is

highly suitable to be applied with smaller spray units hand spray equipment.

It is also suitable for road repair units (RRU) where a selective spraying on specific areas is needed. This Cold road emulsion is extremely suitable due to its favourable and fast breaking point.

The low viscosity emulsion requests a application of fine gravel of 2/6 mm. The required amount of emulsion is approx 1.4 to 1.6 kg per m2 depending on the structure of the surface.

Cold road emulsion will be delivered in barrels or bulk . As is required also with other emulsions there are no special safety requirements needed however it is needed to store the product if frost free environments.

Cold road emulsion meets the below specifications.

Quality control is performed in our laboratories

 

Application                              Concrete :

first sandblast the surface to remove the concrete skinlayer ( making it rough)

spray one layer of Aviron cold road emulsion on the surface ( 1.5 Kg/M²)

Apply +/-10 Kg/M² of broken gravel ( 2-6 mm)

Spray an additional layer of Aviron cold road emulsion p ( 1.5 Kg/M²)

Apply final layer of  broken gravel  (2-6mm) +/-10 Kg/M²

Remove lose gravel by brushing it of

           

Old roofing ( asphalts )

Apply first a fiberglass reinforced layer and Aviron PP 306DR as intermediate layer ( 2.5 Kg/M²)

spray one layer of Aviron cold road emulsion  on the surface ( 1.5 Kg/M²)

Apply +/-10 Kg/M² of broken gravel ( 2-6 mm)

Spray an additional layer of Aviron cold road emulsion ( 1.5 Kg/M²)

Apply final layer of  broken gravel  (2-6mm) +/-10 Kg/M²

Remove lose gravel by brushing it of

 

Old asphalt roads

Use crack fill to fill all cracks making the surface smooth

If needed use one layer of Aviron lavatex 100 on top, thus preventing water penetration thru the asphalt

spray one layer of Aviron cold road emulsion  on the surface ( 1.5 Kg/M²)

Apply +/-10 Kg/M² of broken gravel ( 2-6 mm)

Spray an additional layer of Aviron cold road emulsion ( 1.5 Kg/M²)

Apply final layer of  broken gravel  (2-6mm) +/-10 Kg/M²

Remove lose gravel by brushing it of

 

On gravel roads

Make sure that the top layer of this gravel road is smooth and has a layer of gravel 2/10 mixed with equal parts of sand

Press this layer to min 85 % density

Apply Aviron PP 306 DR as waterproof layer ( 2.5 kg/M²) embed a fiberglass reinforced layer and

spray one layer of Aviron cold road emulsion  on the surface ( 1.5 Kg/M²)

Apply +/-10 Kg/M² of broken gravel ( 2-6 mm)

Spray an additional layer of Aviron cold road emulsion ( 1.5 Kg/M²)

Apply final layer of  broken gravel  (2-6mm) +/-10 Kg/M²

Remove lose gravel by brushing it of

 

 

 

Emulsion                                  type                                          Cationic

 

                                                Sort                                          Unstable (0)

                                                Binder contend                          approx. 65 %

                                                Sieve residue 125 µm                 < 0.5%

                                                Density at 25 °C                        approx 1 Kg/L

                                                Viscosity ( ISO 4 mm – 25 °C)    60-150 sec

Spec. regained bitumen              penetration (100 g, 25 °C 5 s       70-225             

 

 

The Information submitted in this publication Is based on our current knowledge and experience, In view of the many factors that may affect processing and application, these data do not relieve processors of the responsibility or carrying out their own tests and experiments; neither do they imply any legally Binding assurance of certain properties or of suitability for a specific purpose. It is the responsibility of those to whom we supply our products to ensure that any proprietary rights and existing laws and legislation are observed.

 

 

 

AVIRON PRODUCTS LLc

ADMIN OFFICE :                                                                                                           Authorised dealer for

De Vrierestraat 52 – 2000 Antwerp - Belgium  

Tel : ..3232486355  - Fax : ..3232486535                                                                                                           

e-mail : Info@aviron-products.com

webside :         http://www.aviron-products.com

Bank name: LETVIA  “TRASTA KOMERCBANKA” - Account : 1-111-2-10959-1